After use in salt water it is important to wash down the the Boogie to prevent salt build up, corrosion and sand from entering the zipper.  More details on why the motor doesnt require disassembly like a Foildrive motor is found here.

After use in salt water it is important to wash down the the Boogie to prevent salt build up, corrosion and sand from entering the zipper. &#xA0;More details on why the motor doesnt require disassembly like a Foildrive motor is found <a href="https://zerotow.gorgias.help/en-US/maintenance-485284" rel="noopener noreferrer" target="_blank">here.</a><ol><li style="font-size: 16px;">Rinse the remote with fresh water. &#xA0;&#xA0;</li><li style="font-size: 16px;">Rinse the entire Boogie with fresh water. &#xA0;Pay attention to any sand caught under the straps of the trolley.&#xA0;</li><li style="font-size: 16px;">Be careful of the Boogie sliding off the trolley while washing. &#xA0;This could damage the propellor. &#xA0;</li><li style="font-size: 16px;">On the tail cone at the rear of motor there is a small hole, use a water bottle or hose to spray water in there to prevent corrosion of the motor shaft. &#xA0;An occasional spray of lanolin or corrosion inhibitor in this hole is recommended.&#xA0;</li><li style="font-size: 16px;">You do do not need to remove the propeller. &#xA0;</li><li style="font-size: 16px;">Rinse off the rest of the motor mount.</li><li style="font-size: 16px;">A spray of the motor mount with Lanolin won&apos;t hurt, but it is not required.&#xA0;</li><li style="font-size: 16px;">Once the Boogie is rinsed and any sand is removed, dry around the zipper with a towel.</li><li id="isPasted" style="font-size: 16px;">Although the everything inside the Boogie is water resistant it is best practice to keep inside as dry as possible - Dry yourself, get out of your wetsuit before removing the battery. &#xA0;</li><li id="isPasted" style="font-size: 16px;">If you are swapping batteries you can leave a towel inside the Boogie to catch any drips if you are heading straight back out.&#xA0;</li><li style="font-size: 16px;">Open the zip and remove the battery. &#xA0;&#xA0;</li><li style="font-size: 16px; color: rgb(243, 121, 52);">The zip should always be kept in a closed position</li><li style="font-size: 16px; color: rgb(0, 0, 0);">Do not use grease on the battery terminals </li><li style="font-size: 16px;">If the zipper is hard to open place some more silicone lubricant on the external surfaces of the zip as per this <a href="https://tizip.com/storage-cleaning-maintenance/" rel="noopener noreferrer" target="_blank">guide</a></li><li style="font-size: 16px;">Keep the the Boogie, battery and remote and out of the sun at the end of a session.&#xA0;</li></ol>

Wash down procedure after use in salt water

The Boogie has been designed to be as maintenance free as possible.  It uses PVC for the out shell which is 100% corrosion resistant, with the only metallic components exposed to salt water is the anodised aluminum motor mount and the sealed brushles

The Boogie has been designed to be as maintenance free as possible. &#xA0;It uses PVC for the out shell which is 100% corrosion resistant, with the only metallic components exposed to salt water is the anodised aluminum motor mount and the sealed brushless electric motor. &#xA0;The Boogie uses a sealed inrunner motor. &#xA0;The rotor is located on the inside of the stator, and is kept dry using a ceramic seal. &#xA0;What is unique with the Boogie is that the motor is also under positive air pressure because the air in the shell makes it way down the porous phase cables into the motor which gives it another layer of protection. &#xA0;&#xA0;A lot of people will be familiar with the Foildrive system which uses a motor is called an outrunner where the the rotor is located on the outside of the stator and runs wet. &#xA0;This is why corrosion inhibitors and&#xA0;<span id="isPasted" style="color: rgb(65, 65, 65); font-family: sans-serif; font-size: 16px; font-style: normal; font-variant-ligatures: normal; font-variant-caps: normal; font-weight: 400; letter-spacing: normal; orphans: 2; text-align: left; text-indent: 0px; text-transform: none; widows: 2; word-spacing: 0px; -webkit-text-stroke-width: 0px; white-space: normal; background-color: rgb(255, 255, 255); text-decoration-thickness: initial; text-decoration-style: initial; text-decoration-color: initial; display: inline !important; float: none;">disassembly&#xA0;are required after each session.The battery is maintenance free, but needs to be kept between 40- 60% charge, out of the sun and at approximately 20 degrees celsius. &#xA0;Do not put dielectric grease on the battery terminals.&#xA0;The Boogie is running an hour-meter so you do not need to keep track of time spent on the water. In a future firmware updates maintenance alerts will be displayed on the remote.Before/After every session<ol id="isPasted"><li style="font-size: 16px;">The propellor is needed to be replaced if it is chipped or damaged. &#xA0;Using a severely chipped or damaged prop could cause premature motor bearing failure.</li><li style="font-size: 16px;">Check that the Boogie is maintaining air pressure of both the shell and the hull. &#xA0;If there are any leaks find using water and detergent and repair using the included repair kit.&#xA0;</li><li style="font-size: 16px;">If there are air leaks from the motor or the base plate contact support.&#xA0;</li><li style="font-size: 16px;">Check the tow rope for damage.&#xA0;</li></ol>Check to be completed every 10 hours of use.<ol><li style="font-size: 16px;">Check the bolts around perimeter at the front of the motor. If these are loose remove the bolts one by one and use a threadlocker to secure back in place. Red or blue loctite are both ok.&#xA0;</li><li style="font-size: 16px;">Check and tighten the screws and bolts on the steering arm, actuator and actuator mount.&#xA0;</li><li style="font-size: 16px;">Check to ensure the actuator rod is not causing excessive rubbing or wear on the black PVC patch. &#xA0;If there is excessive rubbing contact support.</li><li style="font-size: 16px;">Check the all bolts and threads on the actuator are tight.</li><li style="font-size: 16px;">Check that the prop bolt is tight. &#xA0;Only check the prop with the battery disconnected.&#xA0;</li></ol>250 hours checks<ol><li style="font-size: 16px;">There is no gearbox that requires service.&#xA0;</li><li style="font-size: 16px;">Bearings and seals for the motor may be required after approximately 250 hours run time. &#xA0;Because the motor is under positive pressure this recommended time may be able to be extended. &#xA0;To date we have not had a motor fail.&#xA0;</li><li id="isPasted" style="font-size: 16px;">Bearings and seal kits will be available for purchase, or the motor can be serviced during a refresh.&#xA0;</li></ol>

Maintenance

The Boogie is made from PVC material.  The white colour was chosen as it helps keeps the PVC and the battery cool inside if it is left in the sun. Dark coloured inflatable products can burst if left in the sun due softening of seals/ glues as well as

The Boogie is made from PVC material. &#xA0;The white colour was chosen as it helps keeps the PVC and the battery cool inside if it is left in the sun. Dark coloured inflatable products can burst if left in the sun due softening of seals/ glues as well as the increased pressure from the high temperatures. The down side of white is that is shows dirt, marks and stains easily.&#xA0;To clean the Boogie:<ol><li>First use a mild detergent and scrubbing brush. &#xA0;Externally can get as wet as you like and can be hosed down.</li><li>Underneath the zipper is water resistant, but not waterproof. &#xA0;Wipe inside with a mild detergent and some water. &#xA0;</li><li>For more stubborn stains and marks a slightly abrasive sponge can be used, like a &quot;scrub daddy&quot;</li><li>Isopropyl Alcohol or methylated spirits can be used to help dissolve grease.</li><li>Do not use a strong solvent like acetone, this will attack the PVC and cause damage.&#xA0;</li><li>After cleaning the inside, towel dry, and leave the zipper open for a few hours to ensure no moisture gets trapped inside.&#xA0;</li></ol>

Cleaning and Maintenance

Wash down procedure after use in salt water

Maintenance

Cleaning stains and marks from the Boogie